PUB WS16882018 · Lam Kien Choon BCA L1 ME01 / ME06 / ME12 Mon–Sat 08:00–17:00 · not 24/7 Islandwide Singapore
AOT Heater

Home / Blog / Replacement day

Replacing a water heater: what happens on the day, and how long does it take?

The sequence a licensed crew actually follows in a Singapore flat, what can add a return visit, and what to clear before they arrive. AOT — PUB licensed plumber Lam Kien Choon WS16882018.

AOT storage water heater replacement in a Singapore HDB bathroom

What happens when a water heater is replaced in a Singapore flat?

This guide is for HDB, condo and landed homeowners in Singapore who have already decided to replace a storage or instant water heater, and want to know what the day involves before they book it. The short version: the power and water are isolated, the old unit is drained and removed, the bracket, pipe and isolator are checked, the new unit and a new relief valve go in, the tank is filled and purged of air, then everything is tested and the bathroom is handed back. An instant heater takes 1.5 to 3 hours; a storage heater takes 3 to 5. Nothing in this sequence should be rushed, because the two failures that matter — a tank on live wiring, and an airlocked or leaking tank — both come from skipping a step.

Before the day: three things that decide how the job goes

  • Photos of the existing unit and point. The model plate, the pipe connections, the isolator and the ceiling access panel. This is what lets us quote a real number instead of a range — see the photo quote guide.
  • Ceiling space and support. A storage tank needs 15–25 litres of space above the ceiling and a fixing that carries the weight when full. If the void is tight, the tank position changes before anyone cuts.
  • Whether the unit is in stock. Like-for-like is fast. A different capacity or model may need ordering, which moves the date, not the work.

The day itself, step by step

StepWhat is doneWhy it is not optional
1. IsolateHeater isolator switched off, supply valve closed, sometimes the unit riser shutWorking on a live element or a pressurised tank is how people get hurt
2. DrainTank emptied through the drain cock, air admitted so it drains fullyA full tank cannot be lifted out without damaging the ceiling
3. Disconnect and removeWiring and pipe connections undone, old unit taken out and disposed ofOld unit leaves with the crew — it does not become your problem
4. Inspect what staysBracket, support, pipe size, stop valve, isolator, relief-valve discharge routeA corroded bracket or seized valve fails later, usually within weeks
5. FitNew unit set and secured, new pressure and temperature relief valve, discharge piped to drainA reused valve or a choked discharge is the unsafe part of an old installation
6. Fill and purgeTank filled before power is restored, air bled from the outletsHeating an empty tank destroys the element on the first switch-on
7. Test and hand overPower on, hot water at the outlet, joints checked dry, area cleanedCatches a weeping joint while the crew is still on site

How long a replacement takes

SituationTypical time on siteWhat drives it
Instant heater, like-for-like1.5–3 hoursSimple wall unit, one connection set, no ceiling work
Storage heater, like-for-like3–5 hoursDraining, removing the tank from the void, refilling and purging
Storage heater with pipe or isolator changesAdds a return visitPipe size, stop valve or isolator replaced separately from the unit
Heat pumpSurvey first, then a full dayOutdoor airflow, condensate drainage and support have to be confirmed before ordering

What turns a same-day job into a return visit

  • Seized stop valve or isolator. If the valve will not shut, the supply cannot be isolated cleanly and the valve is replaced as its own job.
  • A different capacity than the old tank. Going bigger needs more ceiling space and a different bracket; going smaller can leave the pipework in the wrong place.
  • Undersized or brittle pipe. Old 15mm runs and brittle CPVC sometimes cannot be reused at the new connection.
  • Concealed leaks behind the point. Damp or staining around the old unit means the wall or boxing is opened before the new heater goes up.
  • Access. A tank boxed in without an access panel, or a riser that needs MCST attendance, adds a separate appointment. See the common heater problems page for what these look like.

HDB flat, condo and landed house

In an HDB flat the work is almost always inside one bathroom, with the tank above the ceiling and the riser outside the unit. In a condo, access to the riser or a common area may need management or MCST attendance, which is booked, not assumed. In a landed house the heater may sit on a roof or in an outdoor enclosure, and that changes the lifting and the weather protection rather than the electrical sequence.

DIY or licensed?

Water service work in Singapore is not a DIY job, and the electrical side is a separate trade. A heater is a fixed appliance holding stored hot water with a live element inside it. If the tank is leaking onto wiring, or the circuit keeps tripping, the heater is switched off at the isolator and left alone until a licensed plumber and an electrician have seen it — that is the same advice as our ELCB tripping guide. Replacement is carried out under PUB plumber licence WS16882018, with the electrical supply checked and signed off as part of the job.

What AOT actually does

Survey first, then a written quote: the existing unit, ceiling space, inlet size and pressure, isolator and relief-valve discharge are checked on site or from your photos, and the labour is quoted separately from the unit. Replacement labour is from S$180 for an instant heater and from S$280 for a storage install; the unit, parts and GST are extra, and the figure is confirmed before work starts. For a like-for-like swap, see the storage and instant pages. Still deciding whether the old unit is worth repairing at all? Start with repair or replace, then check capacity on the capacity guide. Costs across the group sit on the hub at water heater installation cost.

Questions customers ask before booking

How long does a water heater replacement take?

An instant heater changeout is usually 1.5 to 3 hours. A like-for-like storage heater is 3 to 5 hours, because the tank has to be drained, removed from the ceiling void and the new tank filled and purged. If the stop valve, isolator or pipework has to be changed, expect a return visit.

Do I need to be at home during the replacement?

Yes. Someone has to give access to the bathroom, the heater point and the electrical isolator, and confirm the unit and position before work starts. For a ceiling tank, clear the bathroom floor and tell us where the access panel is.

Will the water be switched off?

Yes, to the heater, and often to the unit riser while the supply is disconnected. We tell you before it is isolated and restore it as soon as the new unit is filled and tested.

Can you reuse the old relief valve and bracket?

The pressure and temperature relief valve is replaced, not reused - a seized or choked valve is what makes an old tank unsafe. The bracket and support are inspected and replaced if the new tank is heavier or the old fixing is corroded.

Can it be done the same day I call?

Sometimes, but not by default. We ask for photos first, check stock for the model, then book a slot. Same-day is possible when the unit is in stock and the existing pipework is straightforward.

Do I need approval to replace a heater in a condo or HDB flat?

Inside your own flat or unit, a like-for-like replacement normally needs no building approval. Where the work touches common property, a riser or the building exterior, MCST or management access has to be arranged. Where a submission is required, the licensed plumber handles it and tells you at survey.

Book a replacement, or send photos first

Send the model plate and the heater point on WhatsApp and we will tell you what the job involves before a date is set. Otherwise call during opening hours, Monday to Saturday 08:00–17:00.

WhatsApp +65 8151 8857 Call +65 6816 2462 Email [email protected]

Updated 18 Nov 2026 · Alpha & Omega Trinity Pte Ltd · PUB licensed plumber Lam Kien Choon WS16882018 · BCA L1 ME01 / ME06 / ME12 to 1 Sep 2028 · WICA 21 Nov 2025 – 20 Nov 2026

Powered by biskt AI